The Curta.org Bulletin Board Forum Index The Curta.org Bulletin Board
Welcome to the Curta.org Information Exchange Forum for the Curta Enthusiast Community
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Mechanical purpose of half vs. full adder pins

 
Post new topic   Reply to topic    The Curta.org Bulletin Board Forum Index -> General Questions and Help
View previous topic :: View next topic  
Author Message
dwildstr



Joined: 31 Oct 2018
Posts: 2
Location: Louisville, KY

PostPosted: Wed Oct 31, 2018 7:40 pm    Post subject: Mechanical purpose of half vs. full adder pins Reply with quote

In both types of calculator there are two different types of pins used for carry operations: the "full carry" pin (part #10019) which is a small metal cylinder, and the "half carry pin" (part #10021), which is tapered on the end into a half cylinder. Both types of pins stick out of the counter and accumulator dials (parts #10043 and #10045), with the end result that there are four different types of numeral dials: split-gear wih half-pin (assembly #10203), nonsplit gear with full pin (#10204), nonsplit with half pin (#10205), and nonsplit with no pin (#10045).

Most of this design I understand. The split-gear versus nonsplit-gear distinction is to desynchronize the zeroing process for smoother operation, and the two dials without carry pins are the highest accumulator and counter digits respectively (and thus have no need for carry). But I'm flummoxed by the function of half pins versus full pins: their job is to actuate the carry levers (parts #10005 and #10006), which AFAICT don't much care about the shape of the object striking them. From engineering diagrams of the Type I assembly it looks like the half pins are used on the 4 lowest digits of both the accumulator and the counter, no pin on the highest (unsurprisingly), and full pins on the rest. What's the rationale for this design distinction?
Back to top
View user's profile Send private message
murff



Joined: 27 Oct 2009
Posts: 592
Location: Switzerland

PostPosted: Thu Nov 01, 2018 10:48 am    Post subject: Reply with quote

Here is a picture to this interesting question... (from the Service Manual)



... but really no idea - can't see the functional difference at position 4 and 5:

15 15 16 16 17 18
15 15 16 16 17 17 17 17 17 17 18
_________________
:: m u r f f
:: curta.li
Back to top
View user's profile Send private message Visit poster's website
dwildstr



Joined: 31 Oct 2018
Posts: 2
Location: Louisville, KY

PostPosted: Thu Nov 01, 2018 4:30 pm    Post subject: Reply with quote

Yup, that corresponds closely to both the picture on Rick Furr's Curta poster (which appears to be lifted directly from the service manual but with the numbers changed), and to the arrangement in the engineering diagram for the carriage subassembly first step (assembly #10243).

Interestingly, the Type II, according to its service manual, only uses the half carry pins, which argues in favor of the notion that there was no particular mechanical distinction between the two components, but I'm still curious about the design rationale for using a mixture of the two pin types.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    The Curta.org Bulletin Board Forum Index -> General Questions and Help All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group